The goods sampled out quite satisfactorily.

货物试样结果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好的新鲜试样必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

试样过氧化钠熔融分解,热水浸取、酸化,容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料的水流特性研究，针对不同度的试样，进行常水头渗透试验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度试样疲劳裂纹的“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

试样经火试金法熔炼和灰吹富集后,贵金属王水分解,在盐酸介质中,用火焰原子吸收分度法钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快鱼预混饲料中肌醇含量。该方法具有试样制备简单，分析干扰少，度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给的低铬铸铁下试样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好的冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷的试样具有高耐磨性的重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆金晶的金相及扫描电镜分析试样的制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高钢经硫氮共渗处理后的耐磨性及抗咬性，并与未经表面处理的试样进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石的高质量的二次电子图像所采用的试样制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察试样釉层的显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

试样的偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶金样品过程中的试样分解和分析样品的制备方法进行了较详细的阐述,并列举了几种基体金的具体分析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

试样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过的共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在金属泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%的金属泽釉试样，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物试样结果十满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好的新鲜试样必须在工业酒精纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

试样以过氧化钠熔融解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料的水流特性研究，针对不同粒度的试样，进行常水头渗透试验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度试样疲劳裂纹的“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

试样经火试金法熔炼和灰吹富集后,贵金属合粒以王水解,在盐酸介质中,用火焰原子吸收度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定鱼预混饲料中肌醇含量。该方法具有试样制备简单，析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定的低铬铸铁下试样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好的冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷的试样具有高耐磨性的重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显合金晶粒的金相扫描电镜析试样的制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后的耐磨性抗咬合性，并与未经表面处理的试样进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石的高质量的二次电子图像所采用的试样制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察试样釉层的显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

试样的偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法析冶金样品过程中的试样解和析样品的制备方法进行了较详细的阐述,并列举了几种基体合金的具体析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

试样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过的共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在金属泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%的金属泽釉试样，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物样结果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好新鲜样必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

样以过氧化钠熔融分解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

用某铀矿尾矿作为水砂充填料水流特性研究，针对不同粒度样，进行常水头渗透验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度样疲劳裂纹“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

样经火金法熔炼和灰吹富集后,贵金属合粒以王水分解,在盐酸介质中,用火焰原子吸收分度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

采用离子色谱技术快速测定鱼预混饲料中肌醇含量。该方法具有样制备简单，分析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定低铬铸铁下样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水和空样具有高耐磨性重原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合金晶粒金相及扫描电镜分析样制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后耐磨性及抗咬合性，并与未经表面处理样进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石高质量二次电子图像所采用样制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察样釉层显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

样偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶金样品过程中样分解和分析样品制备方法进行了较详细阐述,并列举了几种基体合金具体分析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

在金属泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%金属泽釉样，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物试样结果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好的新鲜试样必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

试样以过氧化钠熔融分解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料的水流特性研究，针对不同粒度的试样，进行常水头渗透试验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了制厚钢板焊缝断裂韧度试样疲劳裂纹的“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

试样经火试法熔炼和灰吹富集后,合粒以王水分解,在盐酸介质中,用火焰原子吸收分度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定饲料中肌醇含量。该方法具有试样制备简单，分析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定的低铬铸铁下试样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好的冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷的试样具有高耐磨性的重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合晶粒的相及扫描电镜分析试样的制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后的耐磨性及抗咬合性，并与未经表面处理的试样进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石的高质量的二次电子图像所采用的试样制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察试样釉层的显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

试样的偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶样品过程中的试样分解和分析样品的制备方法进行了较详细的阐述,并列举了几种基体合的具体分析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

试样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过的共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%的泽釉试样，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物试样结果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好的新鲜试样必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

试样以过氧化钠融分解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料的水流特性研究，针对不同粒度的试样，进行常水头渗透试验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度试样疲劳裂纹的“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

试样经火试法炼和灰吹富集后,贵属合粒以王水分解,在盐酸介质中,用火焰原子吸收分度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定鱼预混饲料中肌醇含量。法具有试样制备简单，分析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定的低铬铸铁下试样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好的冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷的试样具有高耐磨性的重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合晶粒的相及扫描电镜分析试样的制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后的耐磨性及抗咬合性，并与未经表面处理的试样进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石的高质量的二次电子图像所采用的试样制备法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察试样釉层的显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

试样的偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶样品过程中的试样分解和分析样品的制备法进行了较详细的阐述,并列举了几种基体合的具体分析法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

试样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过的共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在属泽釉配基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%的属泽釉试样，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好的新鲜必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

以过氧化钠熔融分解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料的水流特性研究，针对不同度的，进行常水头渗透验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度疲劳裂纹的“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

经火法熔炼和灰吹富集后,贵属合以王水分解,在盐酸介质中,用火焰原子吸收分度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定鱼预混饲料中肌醇含量。该方法具有制备简单，分析干扰少，速度快，果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定的低铬铸铁下条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好的冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷的具有高耐磨性的重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合的相及扫描电镜分析的制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后的耐磨性及抗咬合性，并与未经表面处理的进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石的高质量的二次电子图像所采用的制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察釉层的显微构,发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

的偏显微镜观察果表明，醇解后，球数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶品过程中的分解和分析品的制备方法进行了较详细的阐述,并列举了几种基体合的具体分析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过的共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在属泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%的属泽釉，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物试样结果十令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好新鲜试样必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

试样以过氧化钠熔融解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料水流特性研究，针对不同粒度试样，进行常水头渗透试验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度试样疲劳裂纹“K法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

试样经火试金法熔炼和灰吹富集后,贵金属合粒以王水解,在盐酸介质中,用火焰原子吸收度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定鱼预混饲料中肌醇含量。该方法具有试样制备，析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定低铬铸铁下试样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷试样具有耐磨性重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合金晶粒金相及扫描电镜析试样制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了速钢经硫氮共渗处理后耐磨性及抗咬合性，并与未经表面处理试样进行了较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石质量二次电子图像所采用试样制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察试样釉层显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

试样偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法析冶金样品过程中试样解和析样品制备方法进行了较详细阐述,并列举了几种基体合金具体析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

试样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在金属泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%金属泽釉试样，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货结果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好新鲜必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

以过氧化钠熔融分解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料水流特性研究，针对不同度，进行常水头渗透验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预制厚钢板焊缝断裂韧度疲劳裂纹“高K比法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

经火金法熔炼和灰吹富集后,贵金属合以王水分解,在盐酸介质中,用火焰原子吸收分度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定鱼预混饲料中肌醇含量。该方法具有制备简单，分析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定低铬铸铁下条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷具有高耐磨性重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合金金相及扫描电镜分析制备技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后耐磨性及抗咬合性，并与未经表面处理进行了比较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石高质量二次电子图像所采用制备方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察釉层显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状黑锰矿体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

偏显微镜观察结果表明，醇解后，球数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶金品过程中分解和分析品制备方法进行了较详细阐述,并列举了几种基体合金具体分析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过共29种真丝织。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在金属泽釉配方基础上，制作了4组户县麦饭石添量为0%，5%，10%，15%金属泽釉，在950℃温度环境下烧成。

The goods sampled out quite satisfactorily.

货物样结果十分令人满意。

The freshly abraded specimen must then be washed in industrial spirit and Analar acetone.

然后，研磨好的新鲜样必须在工业酒精及纯丙酮中洗涤。

The sample was molten and decomposed with sodium peroxide,leached and acidified with hot water and constant-volumed.

样以过氧化钠熔融分解,热水浸取、酸化,定容。

Studied the water flowing characteristics in gangue used as water-gravel-mixed filling material from one Uranic mine.

摘要利用某铀矿尾矿作为水砂充填料的水流特性研究，针对不同粒度的样，进行常水头渗透验。

A high K ratio method for fatigue precracking in welding position toughness specimen of thick steel plate was developed.

提出了预厚钢板焊缝断裂韧度样疲劳裂纹的“高K法”。

After being smelted with fire assay and enriched with cupellation method,the precious metal is decomposed with chloroazotic acid.

样经火金法熔炼和灰吹富集后,贵金属合粒以王水分解,在盐酸介质中,用火焰原子吸收分度法测定钯量。

The inositol in preblend fish feed was detected by ion chromatorgraphy, and the method was simple, rapid and precision.

摘要采用离子色谱技术快速测定鱼预混饲料中肌醇含量。该方法具有样单，分析干扰少，速度快，结果凖确等特点。

The developed dual phase cast steel is applicable as scaleboard materials in a middle or smaller type of ball mill.

在给定的低铬铸铁下样条件下,当冲击载荷较小时,铸态复相耐磨钢具有良好的冲击耐磨性。

The high wearing resistance of the samples after hydrocooling and air cooling was partially attributed to martensite transformation and work-hardening.

经水冷和空冷的样具有高耐磨性的重要原因是其在磨损过程中诱发了马氏体相变,出现加工硬化现象。

A preparation method to reveal the grain boundrie of zirconium and zircaloy for metallographic and scanning electronic microscope analysis is introduced.

介绍了一种能清楚显示锆及锆合金晶粒的金相及扫描电镜分析样的技术。

This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.

研究了高速钢经硫氮共渗处理后的耐磨性及抗咬合性，并与未经表面处理的样进行了较。

In this paper the sample preparation techniques of radiolarite were discussed in order to get high quality secondary electron images in SEM.

讨论了为获得放射虫化石的高质量的二次电子图像所采用的样方法。

The microstructure of the sample glaze layer under polarizing microscope and reflecting microscope has showed acicular hausmannite crystals on the glaze layer sur...

通过偏显微镜和反显微镜观察样釉层的显微结构,发现虹彩釉在成釉过程中釉层表面析出了针状的黑锰矿晶体。

The photographs of polarizing microscope showed the number of spherocrystal was increased and the diameter was decreased after saponification reaction which was agreed with the studies of DSC.

样的偏显微镜观察结果表明，醇解后，球晶数目增加、直径减小、完善程度降低。

The article expounds the sample decomposition and the method of the sample preparation by applying the method of atomical assimilation spectrum, and lists some specific analytical of metallurgy.

本文对应用原子吸收谱法分析冶金样品过程中的样分解和分析样品的方法进行了较详细的阐述,并列举了几种基体合金的具体分析方法。

All the samples include Suzhou satin , Surah and Sangbo satin.There are bleached silk fabrics , dyed silk fabrics and fabrics treated by softener and totally amount of 29 kinds.

样包括素绉缎、斜纹绸和桑波缎，其中有练白、染色和加柔软剂整理过的共29种真丝织物。

The metal reflet glaze samples were prepared with the Huxian wheat-meal-stone accession 0%, 5%, 10% and 15% according to the traditional metal reflet glaze formula and then sintered at 950%.

摘要在金属泽釉配方基础上，作了4组户县麦饭石添量为0%，5%，10%，15%的金属泽釉样，在950℃温度环境下烧成。