The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌高温流态烧过程所产的烟尘,采用回转窑二次烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、烧、球磨工艺制备纳米氧钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯烧法生产高碳石墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧烧—软锰矿浆吸收、烧—选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）烧机。（）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC和热膨胀仪对两种石英砂的原砂和烧砂在加热过程中的相变和热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行了煤基直接还原生产金属团块的研究，提出了润磨造球-预热烧-选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，烧过程中不同镍负载量的催剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还原烧的方法脱除高炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同烧温度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料烧温度和时间等影响因素进行了研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌高温流态化过程所产的烟尘,采用回转窑二次流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、、球磨工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯化法生产高碳墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化—软锰矿浆吸收、磁化—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC和热膨胀仪对英砂的原砂和砂在加热过程中的相变和热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸渣中的铁资源，进行了煤基直接还原生产金属化团块的研究，提出了润磨造球-预热-磁选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还原的方法脱除高炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同温度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料温度和时间等影响因素进行了研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌温流态化焙烧过程所产的烟尘,采用回转窑二次焙烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球磨工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯化焙烧法生产墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC和仪对两种英砂的原砂和焙烧砂在加过程中的相变和进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行了煤基直接还原生产金属化团块的研究，提出了润磨造球-预焙烧-磁选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差及重分析等验证了用还原焙烧的方法脱除炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同焙烧温度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料焙烧温度和时间等影响因素进行了研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌高温流态化焙烧过程所产的烟尘,采用回转窑二次焙烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球磨工艺制备纳米氧化钨铜复合。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

出氯化焙烧法生产高碳石墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC热膨胀仪对两种石英的焙烧在加热过程中的相变热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行了煤基直接还生产金属化团块的研究，提出了润磨造球-预热焙烧-磁选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还焙烧的方法脱除高炉含锌尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同焙烧温度及时间所得的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料焙烧温度时间等影响因素进行了研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌态化焙烧过程所产的烟尘,采用回转窑二次焙烧程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球磨工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指氯化焙烧法生产碳石墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研采用DSC和热膨胀仪对两种石英砂的原砂和焙烧砂在加热过程中的相变和热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行了煤基直接还原生产金属化团块的研，了润磨造球-预热焙烧-磁选-冷固结成型的新工艺程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还原焙烧的方法脱除炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同焙烧度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料焙烧度和时间等影响因素进行了研。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌高温流态化焙烧过程所的烟尘,采用回转窑二次焙烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球磨工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯化焙烧法高碳石墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC和热膨胀种石英砂的原砂和焙烧砂在加热过程中的相变和热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行了煤基直接还原金属化团块的研究，提出了润磨造球-预热焙烧-磁选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还原焙烧的方法脱除高炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时不同焙烧温度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

TiO2用量、SnO2用量、反射材料焙烧温度和时间等影响因素进行了研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法高温流态化焙烧过程所产的烟尘,采用回转窑二次焙烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯化焙烧法生产高碳石墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC和热膨胀仪对两种石英砂的原砂和焙烧砂在加热过程中的相变和热膨胀进行分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行煤基直接还原生产金属化团块的研究，提出造球-预热焙烧-磁选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证用还原焙烧的方法脱除高炉含粉尘中的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行初步的观察，同时对不同焙烧温度及时间所得粉末的红外吸收光谱进行考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料焙烧温度和时间等影响因素进行研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌高温流态化焙烧过程所产的烟尘,采用回转窑二次焙烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

采用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球磨工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯化焙烧法生产高碳石墨较碱法为优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

采用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本研究采用DSC和热膨胀仪对两种石英砂的原砂和焙烧砂在加热过程中的相变和热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

为合利用硫酸烧渣中的铁资源，进行了煤基直接还原生产金属化团块的研究，提出了润磨造球-预热焙烧-磁选-冷固的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还原焙烧的方法脱除高炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同焙烧温度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料焙烧温度和时间等影响因素进行了研究。

The process treating roast dust from zinc pyrometallurgy is,in general,the second roasting by rotary kiln.

处火法炼锌高温流态化焙烧过程所产的烟尘,用回转窑二次焙烧流程。

Composite W-Cu oxide nanopowder was prepared by spray-drying and milling of ammonium metatungstate(AMT) and cupric nitrate.

用偏钨酸铵、硝酸铜通过喷雾干燥、焙烧、球磨工艺制备纳米氧化钨铜复合粉末。

It is proved that preduction of high-carbon graphite by chloridizing roast is better than by alcali.

指出氯化焙烧法生产高碳石墨较法优。

The arsenolite cinders were treated by the processes of oxidizing roasting-pyrolusite pulp absorption,magnetizing roasting-magnetic separation and acid leaching.

用氧化焙烧—软锰矿浆吸收、磁化焙烧—磁选、酸浸工艺处砷华废渣。

Top, the calcinator in the sodium tripolyphosphate plant; above, the atomic absorption spectrophotometer, being used in the laboratory.

（上）焙烧机一角。（下）检验室中的原子吸收光谱机。

During heating,phase transformation and expansibility of the new quartz sands and the calcined Quartz sands from two places were determined by DSC and thermodilatometry.

本用DSC和热膨胀仪对两种石英砂的原砂和焙烧砂在加热过程中的相变和热膨胀进行了分析。

Aimed at utilization of iron resources in pyritic slag,the study on production of metallized agglomerate with pyritic slag through coal based DR process was conducted.

合利用硫酸烧渣中的铁资源，进行了煤基直接还原生产金属化团块的，提出了润磨造球-预热焙烧-磁选-冷固结成型的新工艺流程。

The thermoanalysis results of the catalysts show that interactions between the precursors of nickel and carrier change with the nickel loading during the calcination treatment.

热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。

The feasibility of roasting reduction method to dezinc the Zn bearing BF dust was proved by energy spectrum analysis and differential thermal(DT) and thermo gravimetric(TG) analysis firstly.

通过能谱、差热及热重分析等验证了用还原焙烧的方法脱除高炉含锌粉尘中锌的可行性。

The IR spectra of hydrogel, alcogel and aerogel of BaFe12O19 were studied, and the ones of the powders calcined at different temperatures for different time were also studied.

对钡铁氧体的水凝胶、醇凝胶以及气凝胶的红外光谱进行了初步的观察，同时对不同焙烧温度及时间所得粉末的红外吸收光谱进行了考察。

In addition, this paper studied the influence factor, namely, the mass of TiO2, mass of SnO2, the torrefy temperature and time of the reflect-material, on the capability of the reflect-material.

对TiO2用量、SnO2用量、反射材料焙烧温度和时间等影响因素进行了。